• August 10, 2022

How Many Sprinkler Heads Can You Put On One Valve?

How many sprinkler heads can you put on one valve? At different pressures, the sprinkler head and nozzle will consume different amounts of water. For example, at 35 pounds per square inch (PSI) the 5000 Series Rotor using the 3.0 nozzle will use 3.11 gallons per minute (GPM). If your home's water capacity was 10 GPM, you could place 3 heads per zone.

How many sprinkler zones can I run at once?

Yes, it is often possible to run two valves at once. However there are several problems that can occur. You must have a sufficient water supply for both valves to run at once. If the performance of the sprinklers suffers and you start seeing dry spots in the landscape, you obviously don't have enough water.

Are sprinkler zones connected?

It is connected to a set of valves that regulate the flow of water into a specific "zone" in your sprinkler system. The valves are tied directly into your water system and act like faucets that turn off and on when told to by the controller.

How do you split a zone in an existing sprinkler system?

Can you run 2 sprinkler zones at once?

Running multiple zones at once is usually not possible due water-pressure and flow limitations at residential properties. As with any standard irrigation controller, you can wire multiple solenoids/valves to the same zone output if you want.


Related guide for How Many Sprinkler Heads Can You Put On One Valve?


Why do all my sprinkler zones come on at once?

Water is coming out of multiple zones at the same time: For the valves to stay open in one zone, while shutting outlets in other zones, there needs to be a minimum amount of water pushed through the valve. To investigate further causes and solutions, go to our FAQ page and look under “Indexing Valves.”


How many zones is Hunter Pro C?

Hunter Pro-C PC-400 4 Zone Base Controller; Outdoor Model w/Internal Transformer and Lockable Cabinet. Learn more about free returns.


How do I change the zone on my sprinkler system?


How do I adjust my sprinkler zone?

To adjust a stationary sprinkler head, find the spray radius adjustment screw on top of the nozzle. You may need to adjust it slightly to point the water spray in the direction of your lawn that you want it. Turning it clockwise can also help lower the water pressure on a spray head that is shooting too much water out.


How does a multi zone irrigation system work?


Can I add a drip line to an existing sprinkler zone?


How do you add drip lines to an existing sprinkler system?


How do you install a 2 zone sprinkler system?


Do all sprinkler systems have a master valve?

A master valve is an automatic valve, typically an electric solenoid type valve, that is installed at the point where the irrigation system connects to the water supply. Most, but not all, irrigation controllers have a master valve circuit built in to them.


How do I know how many sprinkler valves I have?

Calculate the number of sprinkler heads for a valve zone by dividing the GPM by your sprinklers' head output, which is listed on the packaging. Round the number down so you don't exceed the capacity of the zone. Sprinkler heads vary in water output depending if they provide a mist spray or stream of water.


How many zones does a solenoid have?

They can be 2-7 zone configurations.


How do I know which sprinkler valve goes to which zone?

Mark each valve with a white paint marker to indicate a zone number that it operates. For future use, make a diagram of your sprinkler system on paper, showing the location of each valve box, each valve and the area it irrigates.


How many drip lines should a valve have?

How many emitters per valve?

Emitter volume used Any water supply that comes out of a building, such as a hose bib. Any system with a pump*. 25mm (1″) water supply. OK to use a 20mm (3/4″) valve.
2,0 l/hr (0.6 gph) 300 700
4,0 l/hr (1 gph) 180 420

How do I increase water pressure in my sprinkler system?

Remove a few sprinkler heads from each of the zones in your system and cap the plumbing that led to them. Decreasing the number of sprinkler heads will increase the water pressure in those that remain. Install a boost pump on the main irrigation line.


How do I connect two sprinkler valves together?


How many solenoids are in a station?

Note: ICC and I-Core can run a combined 4 solenoids by running two programs simultaneously, 2 solenoids on each station terminal.


Why won't one of my sprinkler zones work?

A lawn sprinkler system is usually divided into two or more zones that water independently of each other. Each zone consists of several sprinkler heads controlled by a valve that is electrically activated. If a single zone is not working, the problem is usually an electrical issue or a defective controller or solenoid.


How do you adjust the flow control on a sprinkler valve?


Are sprinkler solenoids interchangeable?

It is also interchangeable with most brands of 24-volt automatic valves. This 24-Volt Solenoid replaces worn Orbit automatic valve solenoids. It is also interchangeable with most brands of 24-volt automatic valves.


How do I add a zone to Hunter Pro C?


What is interval on Hunter Pro C?

Interval Watering is a feature that allows you to select the number of days to pass before the next watering day. For example, an interval of 3 will cycle the program once every three days and water on the third day. An interval of 1 is every day and an interval of 2 will water every other day.


How do I run all Hunter Pro C stations?


Why won't my sprinklers change zones?

Valve Problems

If your sprinkler system isn't working in all zones, chances are the problem is localized to the one or two zones that aren't working. Head out to each valve and see if it is opened fully, broken, rusted, or stuck. Turn valves to the left to open them more. They should have been completely open already.


Was this post helpful?

Leave a Reply

Your email address will not be published.